RC Shock Oil Weight Chart: CST vs WT for Every Setup

Compare RC shock oils by cSt, not brand-specific wt: Tamiya #400 is 400 cSt, while Associated 32.5 wt is 388 cSt; Traxxas wt doesn’t convert directly.
Typical shock oils span 100 to 1,000 cSt, with 400 cSt a medium reference. Choose near your kit’s recommendation, then adjust for track grip, temperature, and piston-hole area: smaller holes need thinner oil.
Thicker oil can calm jump bounce but may feel harsh. The guide helps you refine your setup.
Tamiya and Traxxas Oils
Tamiya labels its silicone damper oils from #100 to #1000, with each number matching the oil’s viscosity in cSt. You can thus match a Tamiya label directly to the cSt column in an RC shock-oil chart; no conversion step is needed. Use the labeled value for direct chart lookup alone.
Traxxas shock oils use a brand-specific weight scale. Don’t read a Traxxas wt label as a standard cSt value or place it directly in the chart’s cSt column. Treat those labels as proprietary weights unless you have reliable, product-specific viscosity data. This keeps your setup decisions grounded in comparable measurements rather than an unsupported numerical match.
Brand Viscosity Cross-Reference
When comparing brands, use cSt rather than wt because weight labels can represent different viscosities.
Compare listed values before choosing oil for your shocks; a matching cSt gives you a defensible starting point across brands. Associated 32.5 wt measures 388 cSt, so it’s the closest listed match to 400 cSt. Tamiya damper oil numbers map to cSt, making #400 equal to 400 cSt. That near-match can spare you a frustrating guess when you need comparable damping.
| Brand | Label-to-viscosity reference |
|---|---|
| Associated | 32.5 wt = 388 cSt; closest listed to 400 |
| Tamiya | #400 = 400 cSt |
Traxxas uses its own wt scale, and the referenced conversion chart doesn’t cover its oils, so don’t infer an equivalent. Cross-reference values rely on manufacturers’ stated viscosities or testing performed by their facilities. Check source and compare cSt before transferring a setup; this helps prevent unwanted handling changes.
Temperature-Dependent Viscosity Changes
As silicone shock oil warms, its viscosity drops, so the shock moves more quickly; cooling makes the oil thicker and slows its movement.
A cSt rating describes viscosity at a specified test temperature. Therefore, two oils’ labeled values may not predict their exact behavior when your shocks operate at a different temperature. Compare oils by cSt rather than brand-specific wt labels, but interpret that comparison with operating temperature in mind.
For a valid setup comparison, measure or test both oils at the same temperature. Also let your shocks reach similar temperatures before you evaluate damping; otherwise, heat differences can obscure the effect of the oil itself. Record test conditions and compare results under controlled conditions when tuning your vehicle on the track and bench.
Typical cSt Shock Ranges
Typical cSt Shock Ranges
RC shock oils typically span about 100–1,000 cSt, from light to heavy, and your vehicle’s setup determines where to start. Use track surface and handling needs to guide your initial choice, then tune from there. When switching brands, compare cSt rather than wt labels; for example, Tamiya #400 is 400 cSt, close to Team Associated 32.5 wt at 388 cSt.
Light Oil Ranges
Light shock oils typically fall around 100–300 cSt, though the practical cutoff depends on your setup and driving conditions.
Tamiya damper oils use cSt-equivalent labels, so Tamiya #100 and #300 correspond directly to 100 and 300 cSt. When you compare brands, match the cSt value rather than the wt label, because manufacturers use different wt scales. That keeps you from treating matching numbers as equivalent viscosities.
For example, Associated 32.5 wt measures 388 cSt, placing it closer to 400 cSt than to the light range. Check your brand’s conversion chart before you choose oil, especially when a label lists only wt. Within the light band, small cSt changes can alter damping feel; test one adjustment at a time and judge the car on track.
Medium Oil Ranges
For medium shock-oil ranges, compare cSt values rather than wt labels, which vary by brand. Use 400 cSt as a practical reference when you’re choosing an oil or changing brands. Team Associated 32.5 wt measures 388 cSt, making it the closest match to that target among the listed options. Tamiya’s damper-oil numbering maps directly to viscosity in cSt, so Tamiya #400 is 400 cSt.
When you compare products, read the chart’s cSt column and match the measured viscosity, not the printed wt number. That approach helps you select a similar medium oil across manufacturers and keeps your setup comparison consistent. Treat each cSt figure as the useful specification; brand labels alone don’t establish equivalence. Use this method for direct, repeatable cross-brand comparisons during setup.
Heavy Oil Ranges
When choosing heavy shock oil, compare cSt values rather than wt labels, which vary by brand. For a target near 400 cSt, Team Associated 32.5 wt measures 388 cSt, making it a close match. Tamiya damper-oil numbers map directly to cSt, so Tamiya #400 equals 400 cSt. These examples show why you should verify the manufacturer’s viscosity data before selecting an oil by its wt label.
Don’t use Traxxas wt labels to estimate cSt through conversion charts made for other brands; Traxxas uses its own scale. Treat each brand’s chart as brand-specific, and match the stated cSt value when you need a precise comparison. Remember that these figures describe shock oil viscosity. Differential fluids commonly span 1,000 to 1,000,000 cSt, far above shock oils.
Track Surface Effects
Track surface helps set a useful starting range for shock oil: smooth, high-grip tracks often suit 400 to 700 cSt, while bumpy or low-grip surfaces typically call for 250 to 450 cSt so the tires stay in contact with the ground. On loose dirt, you’ll often find 300 to 500 cSt useful, with bumps, available grip, and your driving style shifting the effective range. Treat these figures as surface-dependent references, not fixed rules: the same track can demand different damping as grip or roughness changes. When comparing oils from different brands, use their cSt values rather than relying on weight labels, which don’t translate consistently.
Keep front-to-rear balance in view, too. Changing oil at one end affects more than chassis motion; it can alter steering response, traction, and handling.
Setup Starting Points
As a starting point, most RC shock oils fall between 100 and 1,000 cSt, with your vehicle and track conditions determining the useful range. Use that span as a screening range, not a prescription. Start near the oil your kit maker recommends, then adjust in small steps after testing.
When switching brands, compare cSt values rather than wt labels, because manufacturers may assign different viscosities to the same wt number. Tamiya damper oils labeled #100–#1000 correspond directly to 100–1,000 cSt, making those labels straightforward to interpret.
For a 400 cSt target, Team Associated 32.5 wt, at 388 cSt, provides a close match.
Treat Traxxas wt oils separately: their brand-specific scale doesn’t convert through a standard chart. Confirm your choice with careful, repeatable track tests.
Matching Oil to Piston Holes
Match Oil to Piston Holes
Match shock oil to the piston’s total flow area: smaller or fewer holes restrict flow and usually call for thinner oil, while larger or more holes allow more flow and may need thicker oil for similar damping. Consider both hole count and diameter: more or larger openings increase total flow area. Compare viscosity in cSt, not brand-specific wt labels, because identical wt numbers can represent different viscosities.
Change oil in small steps and test the car; piston design, shock speed, and temperature also affect damping. Keep other settings consistent during testing to isolate each change. Record hole count, diameter, piston configuration, and oil viscosity in cSt for every test run, ideally under the same track conditions.
Seal Compatibility and Leakage
Although shock-oil viscosity affects damping, it doesn’t tell you whether the oil is compatible with your seals. Check your shock manufacturer’s guidance for approved oils and seal materials; cSt or wt ratings describe viscosity, not compatibility. Use the specified silicone shock oil and seal lubricant. Don’t substitute differential fluid, which commonly ranges from 1,000 to 1,000,000 cSt and may be far thicker.
Leakage usually signals worn or damaged seals, contamination, or incorrect assembly, not a viscosity change alone. Inspect the shaft and seals for scratches, debris, swelling, or wear; shaft damage can make fresh seals leak quickly. Fill, bleed, and assemble the shock as directed, then check for leaks before you tune damping by changing viscosity. If leakage persists, recheck assembly and replace damaged parts.
Short-Course Jump Landings
When tuning a short-course truck for jump landings, compare shock oils by cSt, since brands’ wt labels use different scales. Thicker oil adds damping and can control chassis bounce after touchdown. But too much damping may make the truck skip across rough ground or feel harsh. Thinner oil lets the suspension move freely to absorb impact, though the chassis may bounce repeatedly.
If you want about 400 cSt, Team Associated 32.5 wt rates at 388 cSt, a close starting match. Check cSt before switching brands; equal wt numbers don’t guarantee equal damping. Tamiya damper-oil numbers correspond directly to cSt, so Tamiya #400 gives you a 400 cSt option for testing landing response. Change oil in steps, then repeat the same jump and compare settling.
Air Bubbles After Filling
After choosing shock oil for landing control, make sure trapped air doesn’t undermine consistent damping. Fill slowly, then leave the cap or bladder loose briefly; bubbles need time to rise before you seal the shock.
- Cycle the shaft gently to release trapped air; rapid pumping can whip more air into silicone oil.
- If bubbles remain, wait several minutes, then repeat settling and gentle cycling before sealing.
- When topping up, match your setup’s viscosity and compare brands by cSt, not wt labels alone.
Once the oil looks clear, close the shock and check its stroke for smooth, repeatable resistance. Persistent foaming suggests you’re cycling too aggressively or haven’t allowed enough settling time; reopen it and repeat the process rather than accepting uneven damping under load.
Pre-Race Oil Change Log
Before race day, log each shock’s oil brand, labeled weight, and cSt so you can compare changes across brands accurately. Track front and rear shocks separately, recording the oil used before each change and replacement viscosity. Add the change date and track conditions to connect setup adjustments with race performance.
- Match oils by cSt, not by the wt label; Associated 32.5wt equals 388 cSt, the closest listed match to 400 cSt.
- Note Tamiya damper oils by their # label, which corresponds directly to cSt; #400 means 400 cSt.
- Review the log before the next race, then change one variable at a time to assess its effect on handling.
Keep entries consistent, and note whether you changed only the front or rear.
Conclusion
Use your chart as a starting point, not a universal prescription. Match cSt values across brands, then account for temperature, piston-hole size, and your vehicle’s weight and landing style. Confirm seals hold the oil without leaks, and bleed each shock until trapped air disappears.
Before race day, record the oil, setup, and conditions; change one variable at a time. That log helps you reliably repeat a predictable setup and tune confidently when the track changes.

